premium “Advanced+ HVAC Service” — a top-tier, all-inclusive package that not only covers deep maintenance and diagnostics, but also incorporates system performance restoration, preventive component upgrades, and data-based optimization.
This is the level for high-value residential systems, commercial clients, or long-term maintenance contracts that demand zero downtime, maximum efficiency, and proactive prevention of failures.
The Ultimate System Optimization & Reliability Package
Designed for clients who expect peak performance, longevity, and full accountability — the Advanced+ Service merges advanced diagnostics, detailed component testing, refrigerant analysis, and energy optimization into one complete package.
This is not just maintenance — it’s a complete HVAC system reconditioning with documented readings and future risk prevention.
Complete deep cleaning of all system components (indoor + outdoor)
Electrical inspection & torque to manufacturer specs
Thermostat calibration and software update (if smart system)
Superheat, subcooling, airflow, and pressure testing
Blower, and coil cleaning
Safety, combustion, and refrigerant diagnostics
Drain line flush and condensate system sanitization
Lubrication of all motors and bearings
Airflow balance testing and temperature mapping
Perform digital system performance report (pre- and post-service)
Log refrigerant cycle pressures, temperature splits, airflow readings
Analyze compressor efficiency curve and current draw trend
Record duct static pressure profiles and compare to design range
Provide digital service report with readings and recommendations
Replace or upgrade capacitors, contactors, and hard start kits as preventive measure
Inspect and service blower bearings, motor shafts, and fan alignment
Re-insulate refrigerant lines with new UV-protected insulation
Clean and protect electrical compartments and control boards from corrosion
Replace drain line safety switches, float sensors, or drain traps if aged
Inspect for micro leaks using electronic leak detector
Add leak sealant or dye if low refrigerant levels are identified
Check for sub-optimal charge conditions and correct
Disinfect evaporator housing, and blower cabinet
Fog system with EPA-registered coil sanitizer (optional IAQ add-on)
Install or maintain UV purification system (if equipped)
Check humidity control operation (humidifier/dehumidifier)
Recommend IAQ or filtration upgrades if needed
Run full system start-up and shutdown sequence test
Verify load balancing across multi-zone or multi-head systems
Provide post-service performance certificate (digital PDF)
Advise on upcoming service intervals or component life expectancy
Approx. 3–5 hours per system, depending on system complexity, access, and refrigerant type.
Annually for high-end inverter or multi-zone systems
Every 12 months (contracted) for commercial clients
Medical facilities, MRI and imaging centers
Luxury homes, multi-zone, or inverter systems
Commercial or multi-tenant properties
Clients with preventive maintenance contracts
Systems with past refrigerant or electrical issues
Owners who value data-backed performance verification
Full digital performance report (before/after readings)
Technician’s notes & photo documentation
Component replacement list (if applicable)
Efficiency rating certificate (for customer records)
premium “Advanced+ HVAC Service” — a top-tier, all-inclusive package that not only covers deep maintenance and diagnostics, but also incorporates system performance restoration, preventive component upgrades, and data-based optimization.
This is the level for high-value residential systems, commercial clients, or long-term maintenance contracts that demand zero downtime, maximum efficiency, and proactive prevention of failures.
The Ultimate System Optimization & Reliability Package
Designed for clients who expect peak performance, longevity, and full accountability — the Advanced+ Service merges advanced diagnostics, detailed component testing, refrigerant analysis, and energy optimization into one complete package.
This is not just maintenance — it’s a complete HVAC system reconditioning with documented readings and future risk prevention.
Complete deep cleaning of all system components (indoor + outdoor)
Electrical inspection & torque to manufacturer specs
Thermostat calibration and software update (if smart system)
Superheat, subcooling, airflow, and pressure testing
Blower, and coil cleaning
Safety, combustion, and refrigerant diagnostics
Drain line flush and condensate system sanitization
Lubrication of all motors and bearings
Airflow balance testing and temperature mapping
Perform digital system performance report (pre- and post-service)
Log refrigerant cycle pressures, temperature splits, airflow readings
Analyze compressor efficiency curve and current draw trend
Record duct static pressure profiles and compare to design range
Provide digital service report with readings and recommendations
Replace or upgrade capacitors, contactors, and hard start kits as preventive measure
Inspect and service blower bearings, motor shafts, and fan alignment
Re-insulate refrigerant lines with new UV-protected insulation
Clean and protect electrical compartments and control boards from corrosion
Replace drain line safety switches, float sensors, or drain traps if aged
Inspect for micro leaks using electronic leak detector
Add leak sealant or dye if low refrigerant levels are identified
Check for sub-optimal charge conditions and correct
Disinfect evaporator housing, and blower cabinet
Fog system with EPA-registered coil sanitizer (optional IAQ add-on)
Install or maintain UV purification system (if equipped)
Check humidity control operation (humidifier/dehumidifier)
Recommend IAQ or filtration upgrades if needed
Run full system start-up and shutdown sequence test
Verify load balancing across multi-zone or multi-head systems
Provide post-service performance certificate (digital PDF)
Advise on upcoming service intervals or component life expectancy
Approx. 3–5 hours per system, depending on system complexity, access, and refrigerant type.
Annually for high-end inverter or multi-zone systems
Every 12 months (contracted) for commercial clients
Medical facilities, MRI and imaging centers
Luxury homes, multi-zone, or inverter systems
Commercial or multi-tenant properties
Clients with preventive maintenance contracts
Systems with past refrigerant or electrical issues
Owners who value data-backed performance verification
Full digital performance report (before/after readings)
Technician’s notes & photo documentation
Component replacement list (if applicable)
Efficiency rating certificate (for customer records)
